Where Have All The Busses Gone?

Astral Fridge Magnet · Sun Jul 27, 2003 11:00 pm

Hello,

As I mentioned in a post not too long ago, I have only recently updated to 3.1c after years of happily using version 2.4a with very few hassles and knowing what I was doing. I wish I could say the same for 3.1c. I prefer 2.4, but I dont get the features of version 3, which I want (the "new" synths for example).
The main hassle I am having is getting my head around the STM mixers>1632 and 16 S.
It doesn't have the same ins and outs as the Big Mixer and where are the Busses? I want to be able to route my audio in Logic to different busses in the Pulsar mixer. I know this might appear to be a stupid question for experienced users, so excuse my ignorance but help!!!

Thanks in advance for your responses.

marcuspocus · Post by **marcuspocus** » Mon Jul 28, 2003 12:20 am

In STM1632 there is no busses, execpt maybe the 4 mono aux send...

The STM2448 have 8 bus with a routing matrix.

Astral Fridge Magnet · Mon Jul 28, 2003 1:01 am

Hi,

WHAT!!!!!! NO BUSSES!!!??? Thanks for going through the trouble of answering. I'll just have to keep using big mixer then. Though is it compatible with version 3?

Post by **garyb** » Mon Jul 28, 2003 1:24 am

Astral Fridge Magnet · Mon Jul 28, 2003 1:56 am

Hi GaryB,

Thanks for your response.

Regards.

King of Snake · Post by **King of Snake** » Mon Jul 28, 2003 3:02 am

On 2003-07-28 02:01, Weirdo The Weird wrote:
Hi,

WHAT!!!!!! NO BUSSES!!!??? Thanks for going through the trouble of answering. I'll just have to keep using big mixer then. Though is it compatible with version 3?

why not use the STM 24/48 then? I'd say this is the real "sucessor" to the BigMixer.

Astral Fridge Magnet · Mon Jul 28, 2003 9:47 am

Hi KIng Of Snake,

The simple answer is that I don't have it.

Well actually I do. In fact I have a total of 3 Pulsar cards. Two pulsar 2 and one Pulsar 1. I haven't installed my Pulsar 2 cards yet, not until I get my new system built. But what I have decided to do is just have the 2 Pulsar cards installed on 1 machine ( the new one to be built) and my Pulsar 1 card will stay on the machine I currently use ( which will be my fuck around machine-pardon the expression). So I will have 2 music making machines.
I have the STM 24/ 48 on my Pulsar 2 cards, my Pulsar 1 doesn't have it.

Regards

aMo · Post by **aMo** » Mon Jul 28, 2003 9:50 am

If you have two pulsar2 cards, why don't you install one pulsar2, and e-mail creamware to transfer one mixer package 1 from pulsar2 to pulsar1?
(Both cards need to be installed for this).

Post by **garyb** » Mon Jul 28, 2003 12:06 pm

bingo.or you could put the p1 and p2 in one machine and the other p2 in the other.that would be the easiest to have all features in both machines........

<font size=-1>[ This Message was edited by: garyb on 2003-07-28 13:08 ]</font>

samplaire · Post by **samplaire** » Mon Jul 28, 2003 4:06 pm

And what's the best in the above solution - you have the extreme ULLI in both machines