Greetings Gentlemen.
I am pretty sure that this issue has been addressed somewhere on the Board but I try with a new post.
I have a Pulsar 1 card installed on my PC and running XP with Cubase 5 and Reason 4.
I have just purchased a Pulsar II with Mix&Master pack. It is upgraded to SCOPE v5.0.
My question is, Can i hook the 2 cards together to get 10 DSP working and what would I need to do this ( cables,software?)
Also If i upgrade to Win 7 are there problems there as well? ( XP is so solid)
Many Thanks AL.
P.S. Bought the card from this site.....
How to Setup Pulsar 1 to Pulsar 2 card ????
-
- Posts: 19
- Joined: Sat Oct 30, 2010 3:44 pm
Re: How to Setup Pulsar 1 to Pulsar 2 card ????
No need to change to Win 7 - you should be able to combine the 2 cards in XP with an STDM cable which you can get from S|C if you dont already have one. The cable hookup is shown in manual.
-
- Posts: 19
- Joined: Sat Oct 30, 2010 3:44 pm
Re: How to Setup Pulsar 1 to Pulsar 2 card ????
Thank you so much for your super quick reply.Have piece of mind now.
Cheers AL
Cheers AL
Re: How to Setup Pulsar 1 to Pulsar 2 card ????
just need the tdm cable stick with xp 32 as its rock solid and all plugs work
as all the samplers dont work in 64bit and a lot of john bowens synth dont work either properly
and the only reason to have 64bit is bigger ram for sample playback streaming libraries like kontakt
and most vsti companies are still using 32bit
even the uhe diva has a 32bit version and sounds sweet even tho a cpu hog
as all the samplers dont work in 64bit and a lot of john bowens synth dont work either properly
and the only reason to have 64bit is bigger ram for sample playback streaming libraries like kontakt
and most vsti companies are still using 32bit
even the uhe diva has a 32bit version and sounds sweet even tho a cpu hog
-
- Posts: 19
- Joined: Sat Oct 30, 2010 3:44 pm
Re: How to Setup Pulsar 1 to Pulsar 2 card ????
Pardon my ignorance,but is the tdm cable stick same as the STDM cable or is it totally different setup.
And where would I purchase one of those?
Cheers AL
And where would I purchase one of those?
Cheers AL
Re: How to Setup Pulsar 1 to Pulsar 2 card ????
same cable best place to buy one is soniccore
but you can easily make them as well with some idc ribbon cable and card conector idc sockets and an idc cable crimper
rs and all other electronic wholesalers sell them 20 pin ribbon and 20 pin card edge idc connectors
but you can easily make them as well with some idc ribbon cable and card conector idc sockets and an idc cable crimper
rs and all other electronic wholesalers sell them 20 pin ribbon and 20 pin card edge idc connectors
-
- Posts: 19
- Joined: Sat Oct 30, 2010 3:44 pm
Re: How to Setup Pulsar 1 to Pulsar 2 card ????
Cool!!!! Thanks Everyone.Fantastic Info.
Cheers AL
Cheers AL
Re: How to Setup Pulsar 1 to Pulsar 2 card ????
Al I've got some spare STDM cables , you can have them .
I'll pop them in the mail to you tomorrow .
Same address , Woombye ?
17 !
I'll pop them in the mail to you tomorrow .
Same address , Woombye ?
17 !
-
- Posts: 19
- Joined: Sat Oct 30, 2010 3:44 pm
Re: How to Setup Pulsar 1 to Pulsar 2 card ????
Thanks Mate for the offer. I already have 2 .
Cheers AL
Cheers AL