How to Setup Pulsar 1 to Pulsar 2 card ????

An area for people to discuss Scope related problems, issues, etc.

Moderators: valis, garyb

Post Reply
alexproskurin
Posts: 19
Joined: Sat Oct 30, 2010 3:44 pm

How to Setup Pulsar 1 to Pulsar 2 card ????

Post by alexproskurin »

Greetings Gentlemen.
I am pretty sure that this issue has been addressed somewhere on the Board but I try with a new post.

I have a Pulsar 1 card installed on my PC and running XP with Cubase 5 and Reason 4.
I have just purchased a Pulsar II with Mix&Master pack. It is upgraded to SCOPE v5.0.
My question is, Can i hook the 2 cards together to get 10 DSP working and what would I need to do this ( cables,software?)
Also If i upgrade to Win 7 are there problems there as well? ( XP is so solid)

Many Thanks AL.
P.S. Bought the card from this site.....
User avatar
dante
Posts: 5045
Joined: Sat Nov 24, 2001 4:00 pm
Location: Melbourne Australia
Contact:

Re: How to Setup Pulsar 1 to Pulsar 2 card ????

Post by dante »

No need to change to Win 7 - you should be able to combine the 2 cards in XP with an STDM cable which you can get from S|C if you dont already have one. The cable hookup is shown in manual.
alexproskurin
Posts: 19
Joined: Sat Oct 30, 2010 3:44 pm

Re: How to Setup Pulsar 1 to Pulsar 2 card ????

Post by alexproskurin »

Thank you so much for your super quick reply.Have piece of mind now.

Cheers AL
jhulk
Posts: 935
Joined: Fri Apr 01, 2011 4:49 am

Re: How to Setup Pulsar 1 to Pulsar 2 card ????

Post by jhulk »

just need the tdm cable stick with xp 32 as its rock solid and all plugs work

as all the samplers dont work in 64bit and a lot of john bowens synth dont work either properly

and the only reason to have 64bit is bigger ram for sample playback streaming libraries like kontakt

and most vsti companies are still using 32bit

even the uhe diva has a 32bit version and sounds sweet even tho a cpu hog
alexproskurin
Posts: 19
Joined: Sat Oct 30, 2010 3:44 pm

Re: How to Setup Pulsar 1 to Pulsar 2 card ????

Post by alexproskurin »

Pardon my ignorance,but is the tdm cable stick same as the STDM cable or is it totally different setup.
And where would I purchase one of those?
Cheers AL
jhulk
Posts: 935
Joined: Fri Apr 01, 2011 4:49 am

Re: How to Setup Pulsar 1 to Pulsar 2 card ????

Post by jhulk »

same cable best place to buy one is soniccore

but you can easily make them as well with some idc ribbon cable and card conector idc sockets and an idc cable crimper

rs and all other electronic wholesalers sell them 20 pin ribbon and 20 pin card edge idc connectors
alexproskurin
Posts: 19
Joined: Sat Oct 30, 2010 3:44 pm

Re: How to Setup Pulsar 1 to Pulsar 2 card ????

Post by alexproskurin »

Cool!!!! Thanks Everyone.Fantastic Info.
Cheers AL
User avatar
MrV
Posts: 247
Joined: Tue May 20, 2003 4:00 pm
Location: Melbourne , Australia
Contact:

Re: How to Setup Pulsar 1 to Pulsar 2 card ????

Post by MrV »

Al I've got some spare STDM cables , you can have them .
I'll pop them in the mail to you tomorrow .
Same address , Woombye ?
17 !
alexproskurin
Posts: 19
Joined: Sat Oct 30, 2010 3:44 pm

Re: How to Setup Pulsar 1 to Pulsar 2 card ????

Post by alexproskurin »

Thanks Mate for the offer. I already have 2 .

Cheers AL
Post Reply