problem with cubase sx3.0

impala64 · Post by **impala64** » Tue Jul 11, 2006 9:34 am

I have a problem when i start cubase.I get the message:
Hardware version 12 detected.This hardware requires a software update.Please consult the installation guide.
Cannot start software because the boards or driver are not properly installed.I have the powersampler 2.Could anybody help me?I have mailled creamware about this problem but they could not help me?

Post by **garyb** » Tue Jul 11, 2006 9:55 am

did you install the driver?

is scope running?

impala64 · Post by **impala64** » Tue Jul 11, 2006 11:36 am

I did install the boards drivers.and scope fusion plattform is running.

ali · Post by **ali** » Tue Jul 11, 2006 11:51 am

make sure you have no conflict between the card and other cards.

make sure that your driver version is 1.50.10.0. try updating the driver in device manager.

make sure when you load cubase that Scope ASIO is selected

and last what software version are you running? are you running SFP 3.1c or Scope 4.0 or older models of powersampler??

the more info you provide the more help is given

impala64 · Post by **impala64** » Tue Jul 11, 2006 12:36 pm

I have the scope fusion platform version 3.1b
installed on my computer.

impala64 · Post by **impala64** » Tue Jul 11, 2006 12:38 pm

My driver version is 1.50.10.0 and i have no conflicts with my soundcard.

impala64 · Post by **impala64** » Tue Jul 11, 2006 12:44 pm

When i start cubase sx3.0 i also get the message that the ASIOMME.DLL is already running.

impala64 · Post by **impala64** » Tue Jul 11, 2006 1:06 pm

where can i find these asio settings?in the routingwindow?

Janni · Post by **Janni** » Tue Jul 11, 2006 1:30 pm

You have to change the ASIO-Settings in Cubase.
It´s like that:
Cubase scanns the computer and finds different ASIO-drivers.
And of course it takes the most common one.
You have to find the menue where you ca set up your drivers and change to ASIO Scope.
Sorry, but I don´t know where to find that in cubase... I´m on Logic, Live and ProTools.
Hope it helps!
Jan

ali · Post by **ali** » Tue Jul 11, 2006 4:36 pm

I don't have 3.0 but in 2.2

Post by **garyb** » Tue Jul 11, 2006 6:03 pm

nice one Ali...

before that setting is made in cubase, be sure to have asio modules(source and dest), with the number of channels you wish to use, activated. THEN open cubase(leaving scope running) and make the appropriate settings.

ali · Post by **ali** » Tue Jul 11, 2006 7:29 pm

absolutely Gary... before you even go into cubase. thanks

impala64 · Post by **impala64** » Tue Jul 11, 2006 9:12 pm

Th cubase program won't start up,so i can't get into the device setup.there is something wrong with my asio drivers.they won't pas the test.ik comes out negative.

Post by **garyb** » Tue Jul 11, 2006 9:43 pm

the test tests the wav(mme) drivers.

put a wav source and dest in the project. cubase will test them, pass them and then start.

wav drivers can be used for other windows programs(like media player or wavelab) and will even allow you to stream other programs in and out of cubase or eachother....

impala64 · Post by **impala64** » Wed Jul 12, 2006 11:35 am

I have re-installed everything, even windows xp.And with succes Cubase is running perfectly.Thanks voor all the cooperation.I have learned a lot. Thanks again.