a SFP does not work with..

arish · Post by **arish** » Mon Jun 10, 2002 8:22 am

I know many poeple had this problem here before, but i can solve it.
_any time i load SFP cubase5.1 does not recognaize The ASIO SCOPE !
and Crash Down !

any body here can throw some input.

I have the win98se and win2000 (both same problem).

arish

subhuman · Post by **subhuman** » Mon Jun 10, 2002 8:53 am

Do you have an ASIO module in your project?

arish · Post by **arish** » Mon Jun 10, 2002 3:03 pm

Yes i do
connected to the mixer.

elektrolurch · Post by **elektrolurch** » Wed Jun 12, 2002 3:45 am

On 2002-06-10 16:03, arish wrote:
Yes i do
connected to the mixer.

Had the same problem after uninstalling Pulsar 3.01. LOGIC didn´t find ASIO drivers.
After reinstalling SFP 3.1 into the same folder as before the same. Then after updating Pulsar driver twice Logic runs! I think there is a problem with the uninstaller of Pulsar and the entries in WIN registry

subhuman · Post by **subhuman** » Wed Jun 12, 2002 8:19 am

Hmmm. Maybe you're right: I never uninstalled Pulsar 3.01, it's still on my machine, and works fine even with the SFP drivers... I have SFP in a different directory. Now that I have moved into SFP completely, I may just delete the Pulsar directory (but I probably won't uninstall)

kiminet · Post by **kiminet** » Thu Jun 20, 2002 4:27 am

I have that problem too.Neither Cubase 5.1 nor SX finds the asio drivers.I installed SFP
and deleted 3.01b.
Could it have something too do with the match of the number of asiodrivers.
Kim

arish · Post by **arish** » Mon Jun 24, 2002 7:43 am

Finally i SFP is running
with cubase recognaizing the asio driver scope after reinstalling the sfp sofware.

but now cubase has hults and cuts in audio with only 12 channels !
any help?

arish

Herr Voigt · Post by **Herr Voigt** » Mon Jun 24, 2002 2:48 pm

With a parallel installation of Pulsar 3.01a and sfp my Cubase couldn't find ASIO too. So I prefered to deinstall pulsar 3.01a. All free devices, old mixers etc. I took into the new spf-folder. So I don't miss 3.01a.
Now Cubase runs without problems. Well, I've never tried, how many channels are possible with my Athlon 1,4 and 512 MB DDR-RAM.
Btw, you have to finetune the new cset.ini if you own cascaded cards like me (Pulsar1, Luna2), cos sfp doesn't recognize this combination as a unit.
Good luck!

<font size=-1>[ This Message was edited by: Herr Voigt on 2002-06-24 15:49 ]</font>

arish · Post by **arish** » Tue Jun 25, 2002 7:50 am

what is cascaded cards ?
and where do i fine tune the cset.ini
and to what do i set it now ?
Thanks

arish

Herr Voigt · Post by **Herr Voigt** » Wed Jun 26, 2002 3:39 pm

Hi arish, please apologize my poor English ...
With "cascaded cards" I wanted to say that 2 or more creamware cards are connected in one computer. A similar word exists in german.
I had to write into my cset.ini:

[hw]
numboards=2

[board0]
boardid=1

[board1]
boardid=0

After writing this, my pulsar1 connected with luna2 are working fine. If you don't own a pulsar1, maybe you don't need to write the entry "numboards=2".
I can load older and difficult projects , too, without a mistake. Once I could not hear any sound in a project with the PulsarMixer (STM 2448). Then I clicked twice on the mono button at the master channel, and it worked.

Greetings from Germany,

Thomas

<font size=-1>[ This Message was edited by: Herr Voigt on 2002-06-26 16:46 ]</font>

arish · Post by **arish** » Fri Jun 28, 2002 5:12 pm

hi yha i do have 2 cards,
pulsar1 and POWERsAMPLAER,
i will try that .
now i have some Latensy problems with pulsar and cubase in small projects,
i can,t find the couse ?
is there is some connection ?

any help on latensy?

about english do not worry we all have some mistakes here and there

arish