PulsarII ASIO/busses routing problem with nuendo2 PLS HELP M

pulsarian2 · Post by **pulsarian2** » Mon Jun 30, 2003 4:06 pm

Pls i need an help.
Using Sfp31c
First of all i set asio dest and asio source at 32 channel.( for to be sure i dont wrong)
Now

I want that an audio track plays on asio ch 3 and 4 etc etc and not always on 1 and 2.
How to set that audio track in order that plays on Asio channel 3 or 4 etc etc??

I add more stereo out in vst connections but but always shows me only out1 and out2 under ASIO Device Port(I set 32ch IN and 32ch OUT before run Nuendo2)
tks a lot

dehuszar · Post by **dehuszar** » Mon Jun 30, 2003 6:58 pm

Sounds like you've got SFP set up right. Make sure that you have additional busses set to 'active' in Nuendo. Then you should be able to use Nuendo's Inspector to select the appropriate outputs. At least in Cubase SX, the Bus Hotkey is F4.

This stuff will all be in your Nuendo manual.

Sam

pulsarian2 · Post by **pulsarian2** » Tue Jul 01, 2003 12:07 am

i am sorry dehuszar
but in Nuendo2 there is not button to switch ON/OFF busses.
There is no page for busses only in vst connections u can add busses but not showen on output for busses

pulsarian2 · Post by **pulsarian2** » Tue Jul 01, 2003 12:07 am

i am sorry dehuszar
but in Nuendo2 there is not button to switch ON/OFF busses.
There is no page for busses only in vst connections u can add busses but not showen on output for busses

dehuszar · Post by **dehuszar** » Tue Jul 01, 2003 1:03 am

Okay, well I'm used to SX. That's strange though. I've fiddled with Nuendo and found it to be pretty similar in feel and functionality.

Better check in the manual. I'm damn near positive that Nuendo has BUS ON/OFF buttons or something. I just don't know if you get to it the same way or what, but there has to be a way to turn more busses on.

Try hitting F6 first and see if that gives you a full list. It should allow you to add a whole bunch of busses, then hitting F4 will allow you to turn those busses on/off. But if it's like SX (which it may not be in this respect) the busses won't show up until they've been added to the list.

Hope that helps ya,

Sam

Kenf · Post by **Kenf** » Tue Jul 01, 2003 2:02 am

Hi
I am not a Neundo user either I to use SX. In SX under the 'Devices' menu there is 'VST outputs' This shows a panel as pulsarian2 describes. If you do find it you may have to 'drag' the window further open to see all the channels. I got caught out at first as I could only see channels 1/2 but when I opened the window more they were all there!You can then turn the channels on/off and change the scope outputs they are connected to. You could try a search under the help menu? Keep at it!

december · Post by **december** » Sun Jul 13, 2003 6:18 am

I have N2 and have not found a solution yet.
Nor have the support team responded to my questions.
Nuendo 1x used to show the outputs automatically, after they were connected, then you could turn them on or off, but 2.0 does things differently. You can add more I/O busses, but when you determine their source or destination, the only choices given are the physical (stereo) I/O.
This is a serious problem that is not being addressed.
I want to use 32 I/O so I can route gigastudio channels directly into N2.

I guess we are in the minority since no one in the Nuendo forum is helping.

<font size=-1>[ This Message was edited by: december on 2003-07-13 07:19 ]</font>