MasterIT loud peep when loading

[Inferman]

Hello there,

It's quite old and annoying problem I every time forget to share and maybe it's already solved a long time ago.
But I didn't find this issue with search "MasterIT"

Everytime I load MasterIT I hear very loud short peep. It's extra brutal sound when I work with heightened volume

Is there any solution for it? Am I using unfixed .sys files or smth?

Thanx a lot for Your advices! I love MasterIT, but this nuance is a bit disappointing.

[dante]

I get that noise every time I start Scope, whether MasterIT is there or not. But never on project or Masterit load.

Are you talking about 'Every time I load a project that has MasterIT in it' or about 'every time I add MasterIT to an existing project' ?

[Inferman]

Dante, I hear loud peek everytime I add MasterIT to any project.
Not noise, but loud squeak.

I made some short video, please check:
http://tinypic.com/r/291kv7r/8

I add GraphicEQ (as an example of any other plugin), and then I add MasterIT.
Don't forget to listen with moderate (not high) volume, please ))

[Music Manic]

Maybe your card drivers or the file is corrupt. Try reinstalling.

Is there any audio signal attached to the file while it's imported? Does turning the fader down make the sound disappear?

[Inferman]

Music Manic, already tried to reinstall drivers... Twice )

Is there any audio signal attached to the file while it's imported?

Sorry, I don't quite got it )) You mean in Scope project? Well, if I add MasterIT into Mixer channel which connected with ASIO - yes, peek is appeared.
If I add MasterIT into Mixer chennel which has no input connection - peek is absent.

And yes, if I make master fader to -inf, peek is absent too.
This peek seems generated by MasterIT and it's just like any other signal - flows by route connections and has it's own loudness I can manipulate with any faders on mixer\control rooms.

[JoPo]

Here, Master it doesn't make any sound when loading it but Fat Cat does !

But no bad sound when loading a Scope project with Fat Cat inside.

[Music Manic]

Tried it, and like most plugins the audio cuts off while loading,without any noise. I am on 5.1.

Have you tried re-installing Scope?


I remembered a loud squeal a long time ago but it was to do with z-link.

[Inferman]

Here, Master it doesn't make any sound when loading

But it does =(( Please, check the video above, every time I open MasterIT (in mixer chennel which route output signal to speakers), it squeals
If I add MaterIT in routing window there is no sound, because this module disconnected.

Music Manic, I have the simpliest routing ever )) Xite connected to computer via pci-e and xite connected to speakers.
Tonight I'll try to reinstall scope and MasterIT.

[Music Manic]

Dante, I hear loud peek everytime I add MasterIT to any project.
Not noise, but loud squeak.

I made some short video, please check:
http://tinypic.com/r/291kv7r/8

I add GraphicEQ (as an example of any other plugin), and then I add MasterIT.
Don't forget to listen with moderate (not high) volume, please ))

Ahh! I see you had the graphic EQ loaded first. That's what's causing the problem I believe. Mine use to make that noise too.

Try a project with just the MasterIT plugin. I think the Graphic EQ causes problems.

[Inferman]

Music Manic, I'm afraid it's vice versa - everything fine with GraphicEQ and any other plugin.
I open GraphEQ as example of any other plugin.

I can open 10 different plugins, and 11th MasterIT will squeak.
I can open 5 plugins, squeaky MasterIT, and then 5 others (with no sounds).
I can open just MasterIT with squeak.
I can open three MasterIT with three squeaks.

Everytime in any combination MasterIT is a reason ((

[Music Manic]

Music Manic, I'm afraid it's vice versa - everything fine with GraphicEQ and any other plugin.
I open GraphEQ as example of any other plugin.

I can open 10 different plugins, and 11th MasterIT will squeak.
I can open 5 plugins, squeaky MasterIT, and then 5 others (with no sounds).
I can open just MasterIT with squeak.
I can open three MasterIT with three squeaks.

Everytime in any combination MasterIT is a reason ((

Does it happen if you load MasterIT first in a fresh project? Have you replaced the MasterIT module with a fresh copy?

[Inferman]

Does it happen if you load MasterIT first in a fresh project? Have you replaced the MasterIT module with a fresh copy?

Yes and yes.
And I can tell You more - I load MasterIT in empty routing window, and quickly double-click on it.
I see the out level is fading down just as after loud signal. I don't hear it because module is disconnected but if I link MasterIt with Dest - it squeaks

I reinstall Scope and reinstall MasterIT - nothing changes...

[Music Manic]

Ok so it's not the files. Something must be affecting it. What is your hardware setup? Is Scope the master clock? What samplerate are you running at?

[Inferman]

I'm running Windows 8 x64
XITE-1 is a Mster clock.
Sample rate is 44.1 kHz

By the way, in 96 kHz this squel is two time higher and two time faster.

[Inferman]

Yes, I found it!
It was because of the file, actually. Masterit.dev
I use old (x86) version of MasterIT instead of special x64 edition (which is in /plugins/_64 Bit_OS_Versions/DAS/ on soniccore website)

Squeaks is gone now! Thank You all for support

[Music Manic]

Yes, I found it!
It was because of the file, actually. Masterit.dev
I use old (x86) version of MasterIT instead of special x64 edition (which is in /plugins/_64 Bit_OS_Versions/DAS/ on soniccore website)

Squeaks is gone now! Thank You all for support

That's what I thought first. Glad you sorted it. Shame the Squeal wasn't musical.