With 3 or 4 ms latency my Creamware PowerPulsar ...

tribadism · Post by **tribadism** » Sun May 05, 2002 2:19 pm

With 3 or 4 ms latency my Creamware PowerPulsar ( wave dest ) don't work with soundforge 4.0 or wavelab 3 ....

I don't habilitate at record ...

My system .

AUSU P4B266

install INF and Intel acc.

Powerpulsar z-link

Version Pulsar 3.01b

tribadism@inwind.it

Thank

subhuman · Post by **subhuman** » Mon May 06, 2002 9:12 am

What OS?

What PCI slot is your PowerPulsar in?

tribadism · Post by **tribadism** » Mon May 06, 2002 9:17 am

Win98 SE

3° Slot

Thank Subhuman

subhuman · Post by **subhuman** » Mon May 06, 2002 9:22 am

One more question: what is your CPU speed?

I can run 3ms <i>barely</i> on my 1.8Ghz.. if you have a 1.6A then 4 or 7ms will be better settings to use.

Anything sharing an IRQ with your card? You can check with "Winkey+Pause" combo, Device Manager, Properties... if you could put that list here, it would make the troubleshooting quicker/easier from this end. Thanks!

tribadism · Post by **tribadism** » Mon May 06, 2002 10:11 am

[quote]
On 2002-05-06 10:22, subhuman wrote:
One more question: what is your CPU speed?

2.14 mhz ( overclock ) original is 1.8a

I can run 3ms <i>barely</i> on my 1.8Ghz..

I have the same CPU

if you have a 1.6A then 4 or 7ms will be better settings to use.

Anything sharing an IRQ with your card? You

Sharing with ACPI !

tribadism · Post by **tribadism** » Mon May 06, 2002 10:39 am

I made a test

If my pulsar project cancels and puts again

wave dest 1, wavelab or sound forge RECORD !!!!!! works fine .

If I stop recording and try again it doesn't work but if I cancel wave dest 1 and put again .... WORKS FINE !!!! WHY ???

tribadism · Post by **tribadism** » Mon May 06, 2002 10:52 am

attention

ULLI at 44.1

set at 3ms don't work
set at 4ms don't work

at 7 / 13 or 25ms work fine

subhuman · Post by **subhuman** » Mon May 06, 2002 11:13 am

ACPI is holding your latency back. Reinstall XP in Standard mode or change HALs. For more information on ACPI/Standard and switching visit the Optimize your Win2k/XP thread in the Tips & Tricks section here.

tribadism · Post by **tribadism** » Mon May 06, 2002 11:20 am

On 2002-05-06 12:13, subhuman wrote:
ACPI is holding your latency back. Reinstall XP in Standard mode or change HALs. For more information on ACPI/Standard and switching visit the Optimize your Win2k/XP thread in the Tips & Tricks section here.

I don't have Windows XP

. I have only win98 SE ...

What is HALs ????

Is possible disable ACPI into win98 SE ?

Thank Sub

))

subhuman · Post by **subhuman** » Mon May 06, 2002 11:39 am

Oh, sorry, I read that you were using 9x and then forgot. Very strange results, are you using an older project or something? Anyway if it works then stay with it!

tribadism · Post by **tribadism** » Mon May 06, 2002 12:00 pm

On 2002-05-06 12:39, subhuman wrote:
Oh, sorry, I read that you were using 9x and then forgot.

No problem

Very strange results,

You think ? Why don't you try to make a test? with PowerPulsar and win98 SE ?

are you using an older project or something?

My test is ONLY wave dest 1 ....

Anyway if it works then stay with it!

:|