clock di scope utboard is to be synchronized

nunziata · Post by **nunziata** » Sun Feb 24, 2008 1:19 am

utboard is to be synchronized
1 scope DSP
A16 ultra 1
1 presonus digimax
1 Roland M1000
Thanks

alfonso · Post by **alfonso** » Sun Feb 24, 2008 1:23 am

Could you explain your problem a bit better?

nunziata · Post by **nunziata** » Sun Feb 24, 2008 2:47 am

How do I synchronize machines?
Samplerate scope of the errors I
As devop do?
Whereas outboard
Scope DSP 15
Zlink connected with A and B ultra a16
Presonus digimax
M 1000 Roland mixer
And a signal distributor MUTEC 1 in 8 out?

H-Rave · Post by **H-Rave** » Sun Feb 24, 2008 1:53 pm

start off as the scope as master with adat and syncronise the a16 ultra the presonus digimax off that, maybe go out of the digimax with the bnc into the mutec, they will all have to be switched on of course, oh and don't panic, unless you're recording the rolling stones and then you can panic.

nunziata · Post by **nunziata** » Sun Feb 24, 2008 10:49 pm

In the project that I have inciato in zlink dest must connect the monitors.
For listening.
Right?

Post by **garyb** » Sun Feb 24, 2008 10:59 pm

maybe. you can use the A16 via z-link to the monitors or you can use the analog or sp/dif connectors to the monitors depending on how you set up your project. Scope is a virtual reality patchbay. connect as you please.

nunziata · Post by **nunziata** » Thu Feb 28, 2008 2:03 pm

Hello, but the form syncplate where you connect?
What?
Perhaps we need to set 16 as the master if you want to use the 16 channels

Post by **garyb** » Thu Feb 28, 2008 6:01 pm

no the A16 doesn't need to be master. if you are using the syncplate, the connections are external bnc. within scope, you select bnc as master, OR if scope is set to master, clock will be transmitted through bnc and adat.

nunziata · Post by **nunziata** » Thu Feb 28, 2008 10:14 pm

But because 'I will not do a project?
Like 'I see the better argument:
Example hardware I.
Thanks a lot

Post by **garyb** » Thu Feb 28, 2008 11:35 pm

obviously there's a language problem.

nunziata · Post by **nunziata** » Fri Feb 29, 2008 5:53 am

No problem, just send a project that displays what has been said.
There is a problem doing this?
Thanks

Post by **garyb** » Fri Feb 29, 2008 12:45 pm

yes. if i unerstood you and you understood me i could just tell you.

i don't understand the problem.

you don't need to do anything special to sync samplerates in the project. no syncplate module is required.

nunziata · Post by **nunziata** » Sat Mar 01, 2008 12:48 am

Yes, but regardless if I can not put it, the project can mandarmelo?
So 'schiarisco my best ideas.
This was my initial application.
Thanks anyway

Post by **garyb** » Sat Mar 01, 2008 1:05 am

mandarmelo?
'schiarisco?

H-Rave · Post by **H-Rave** » Sat Mar 01, 2008 2:43 am

Babelfish

Post by **garyb** » Sat Mar 01, 2008 3:13 am

sure is...

nunziata · Post by **nunziata** » Sat Mar 01, 2008 10:57 pm

Sorry for my English.
Through the same

Post by **garyb** » Sun Mar 02, 2008 12:24 am

no problem. sorry i couldn't help.

H-Rave · Post by **H-Rave** » Sun Mar 02, 2008 4:40 am

Nunziata :

Through the same

Stop it !

That's my Idea ??

nunziata · Post by **nunziata** » Sun Mar 02, 2008 5:32 am

Ok but who is the master?

PlanetZ forums - scopeusers.com

clock di scope utboard is to be synchronized

clock di scope utboard is to be synchronized

How do I synchronize machines?

hello

Hello, do you know syncplate?

please help me

nothing problem

Excuse my insistence

ok