The basic rewire?

RobY_surf · Post by **RobY_surf** » Thu Dec 14, 2006 3:05 pm

mmm hi!
im just looking for a simple project. i want to see how do i rewire a synth to cubase. can somebody show me please?
Thanks.

at0m · Post by **at0m** » Thu Dec 14, 2006 3:31 pm

Howto route a DSP synth to Cubase? Connect it to an ASIO Dest. Then in Cubase you can record it.
We usually don't monitor to ASIO Dest, since that adds extra latency. But you could put VST inserts on monitoring-enabled track, and if needed let Cubase play its controlling MIDI a bit earlier so it compensates for the added ASIO latency.

RobY_surf · Post by **RobY_surf** » Fri Dec 15, 2006 12:37 am

mmm... I Didnt follow that..
This is my routing window.
And what am i doing in cubase VST connection?

I don't want to recored the synth, i just want to rout it to cubase so i could play it in a MIDI Track?
sorry for the troubles.
Thanks alot for helping.

arela · Post by **arela** » Fri Dec 15, 2006 1:03 am

conect Scope MIDI source to synt midi in - then route the audio from the synth to the mixer

NB! This is routing - don't mix it up with rewire - a Proppellerhead protocol.

arela · Post by **arela** » Fri Dec 15, 2006 1:15 am

and in cubase

RobY_surf · Post by **RobY_surf** » Fri Dec 15, 2006 2:06 am

It doesn't work man..
Can you help me finding the problem?
Cubase showing that there is a sound, and still, not a sound..

See picture -

Thanks alot.

Post by **hubird** » Fri Dec 15, 2006 3:00 am

The module Pulsar Midi A source points to the hardware Midi input on your Pulsar card...
Use the Midi sequencer module instead to connect to Cubase.

You should study the manual for a while, it's explained very well.
Midi is not ASIO by the way, Midi is not 'sound'... (you say 'Cubase showing that there is a sound, and still, not a sound..').
SFP works just like an analog classic studio where you have to connect everything with cables, but
the thing as a whole is not a toy, so take the time to read the f. manual

arela · Post by **arela** » Fri Dec 15, 2006 4:55 am

Like Hubird says:

The module Pulsar Midi A source points to the hardware Midi input on your Pulsar card...
Use the Midi sequencer module instead to connect to Cubase.

You can combinde this with the midi merger.
Pulsar midi > synth let you play the synth thru scope, and you can record midi to cubase, while seq midi to synth plays your cubase midi track with scope synth.

You better change Cubase MIDI IN to NO MIDI SOURCE when you have finished midi recording, or you might se a midi loop

i forgot; connect Seq midi dest to merger

katano · Post by **katano** » Fri Dec 15, 2006 5:08 am

omg, rtfm

ftp://ftp.creamware.com/Manuals/SCOPE/M ... rivers.pdf

have a read on the chapter "driver interfaces", it's explained very well i think...

cheerz
roman

arela · Post by **arela** » Fri Dec 15, 2006 6:54 am

yes katano, it's well explained in the manual, but the merger is a secret weapon

RobY_surf · Post by **RobY_surf** » Fri Dec 15, 2006 9:43 am

Thnx it works!
Happy happy happy:)
The manual doesnt include cubase configuration in it.
The biggest problem was how to configure in cubase.

Sorry for all the writing mistakes

arela · Post by **arela** » Fri Dec 15, 2006 1:46 pm

we dotn acpect masstajks

RobY_surf · Post by **RobY_surf** » Fri Dec 15, 2006 5:17 pm

This is what happens if you're doing music at home instead of learning for an english test. Sorry.

mmm

arela · Post by **arela** » Sat Dec 16, 2006 1:21 am

have fun - guess you have some sounds to make

RobY_surf · Post by **RobY_surf** » Sat Dec 16, 2006 3:49 am

So, im having alot of fun using SFP synth in cubase.
I did some exploring in this area and it seems and sound (!) that scope's FX are very good !
I managed to rout it with a SFP synth but i was thinking, can i rout an FX to a regular Cubase vst?
Or an Audio Channel?

Thanks and sorry again

Post by **hubird** » Sat Dec 16, 2006 7:34 am

The normal way to do this is to route the VSTi out of Cubase thrue an ASIO bus, and apply the fx on it, be it in the project window itself by cabling it, or by inserting it in the mixer's channel which holds the VSTi sound

XTC is another story, I don't and even can't use it (I'm on mac, XTC is not supported on mac).

RobY_surf · Post by **RobY_surf** » Sat Dec 16, 2006 12:21 pm

O.k so how do i do it?
How do i rout the VSTI out to scope? and more..
thanks..

Post by **hubird** » Sat Dec 16, 2006 2:11 pm

You must activate a few extra 'busses', open the Master mixer of Cubase, pull the window to the right (I'm still on an old Cubase, but it will work similar I guess).

These busses are not busses like the usual mixer table 'busses', it are ASIO busses, plugging audio channels to other ASIO software inputs, like the SFP ones.

Make sure (before opening Cubase) you have extra busses choosen in your SFP ASIO Source module.

Having done this, output the Cubase mixer track that holds the audio of the VSTi to the ASIO bus of your choice.

RobY_surf · Post by **RobY_surf** » Sat Dec 16, 2006 5:28 pm

"pull the window to the right"
mmm.. i would like a picture if its ok with you..
I cant find any busses..

arela · Post by **arela** » Sat Dec 23, 2006 2:22 pm

Something like this

PlanetZ forums - scopeusers.com

The basic rewire?

The basic rewire?

.............

....

Mmm

So

..

...