Page 1 of 1
Posted: Fri Oct 11, 2002 11:09 am
by guitarcat
have a Pulsar2 Card (Classic I/O)...now the following thing happens...i always thouhgt i'm wrong but now i'm 100% sure that it's not my fault...always when i try to sync something to ADAT A the LED is flashing around like crazy...i have no idea why...the strange thing is it happens only @44.1khz...with 48khz everything works perfect...i tried it both ways...set Pulsar to Master doesn't work and even if i slave it...only a flashing LED in the Saplerate-Settings...isn't that strange...with the ADAT B Port i have no Problem at all...is my ADAT A port broken or is it a BUG...i need both ports because i record from my Yamaha 01v and my Motu 2408mkII...any ideas???...please help!!!
thanx
guitarcat
Posted: Fri Oct 11, 2002 5:10 pm
by sandrob
wellcome, guitarcat!
i'm sorry about your problem, but i can't help you.
people here are helpfull but you have strange problem.
did you ask cw for help? what they say?
Posted: Fri Oct 11, 2002 8:35 pm
by garyb
well,i don't want to say ot even one more time,but i must say it again.if all else fails format the drive and reinstall.sometimes computer data becomes corrupt.if that doesn't work,well maybe there is a hardware problem...tried swithing cables?tried useing canned air to clean the adat ports?
all just random shots in the dark........
Posted: Sat Oct 12, 2002 2:12 am
by guitarcat
thanx for the answers!...i checked all...but nothing helped...looks like a hardwareproblem...as looks like i have to record my stuff in 48khz and then sampling down to 44.1khz...i think i can live with that...thanks again...
guitarcat
Posted: Sat Oct 12, 2002 2:35 am
by at0m
Resampling is not a good thing to do.
I suppose you've:
-checked and swapped cables,
-cross-wired to see if it isn't the non-CW ADAT port that flips,
-checked your mixer's spec's
-tried both devices as Sample Rate Master (one at once of course;)
-if the ADAT A keeps refusing, can you sync via SPDIF and then sync the ADAT automatically along?
-...
Posted: Sat Oct 12, 2002 5:05 am
by guitarcat
i checked everything believe me...nothing helped!!!...but thanx anyway...
guitarcat
Posted: Sat Jun 21, 2003 6:25 am
by es1276
Same problem here.
Any comments ?
<font size=-1>[ This Message was edited by: es1276 on 2003-06-21 07:25 ]</font>
Posted: Sat Jun 21, 2003 1:15 pm
by astroman
someone correct me if I'm wrong, but if you want to use the Pulsar, the Yamaha and the Motu simultaneously there's only one possible setup: the Pulsar must be master and both the other units have to slave to it.
Otherwise you'd have to provide a separate clock via BNC and syncplate.
cheers, Tom
Posted: Wed Jun 25, 2003 4:26 am
by es1276
I think it´s not a setup problem like master/slave settings or cables.
It only happens occasionally with ADAT port A at 44.1 kHz. (see guitarcat´s posting above)
<font size=-1>[ This Message was edited by: es1276 on 2003-06-25 07:08 ]</font>
Posted: Thu Jun 26, 2003 9:58 am
by astroman
actually I referred to the first post of the topic. Guitarcat tried various setups, but there is only one choice possible for the 3 devices to run together.
Pulsar master and the other devices slave - anything else is bound to fail.
It may not be noticable at once under certain circumstances. From time to time my adat mixer runs quite well without sync. With lot of distorted sound it might be even more difficult to notice
Unfortunetely (if you have the correct setup) it's impossible to decide if the error is caused by hardware failure or by a missing or damaged software module.
Both cases have been reported
cheers, tom
Posted: Tue Jul 01, 2003 12:33 pm
by es1276
I think one Pulsar II with one A16 (the old one) is a quite easy setup, isn´t it ?
there should be a way to make it work.
Any ideas ?