PlanetZ forums - scopeusers.com

Hello all,

Last week, a power spike fried my Pulsar II, and Creamware was kind enough to send me a new one. I've been using software version 3.01, but after installing the new card, I was stupid enough to install the updated v3.1 into the same folder where v.3.01 was housed, causing a great, big mish-mash of Pulsar software versions. I uninstalled
everything in those directories, but now I've got a strange problem that I fear can only be remedied by wiping my drive and re-installing Windows and everything else...

Pulsar works for me, however there's a whole lotta plug-ins that give me a registration prompt when I try to open them (ex. Auto-Wah M & S, Softclip M & S, TQ Drive M & S, Midi Pole M & S, Master Flanger M & S, to name just a few) asking me for my software serial number and an activation key for the plug in.

Possibly problematic is the fact that when I registered my new Pulsar II, my activation page did NOT include an updated Pro Pack activation key (since the "Pro Pack" no longer exists), so I had to use my old key.

On the other hand, I recieved no messaging alerting me to incorrect activation keys and everything else seems to be running properly on the Pulsar as far as I can tell.

Is it possible that this has something to do with invalid activation keys? Otherwise, I'm afraid that in my various attempts to install and unistall Pulsar software today I somehow damaged Windows 98 and the only resolution would be to wipe my drive and start over. Before I take this drastic, time consuming, and possibly fruitless step, is there any thing else at all that anyone can offer me as a possible solution?

THANKS,

--Doron
323.229.0822

Read the readme.rtf in the folder from where you install SFP. There should be new keys for all CW devices and stuff you bought in the shop.

Pulsar (New customers or existing customers with Pulsar ProPack) / PowerPulsar

Main Studiotools Package
DSP Effects: MasterVerb, MasterVerb Classic, compressor, limiter, gate, expander, parametric EQ, 4-pole filter, high-cut filter, low-cut filter, chorus, flanger, phaser, delay, dual delay, distortion.
Studio Tools: STM 1632 - 16/32-channel recording mixer, STM 16 S - 16-channel 5.1 surround mixer, VRC-S - ADAT Remote Control Unit, various audio tools (Control Room, Aux rack, etc.), various MIDI tools (monitor, merger, splitter, etc.)

Synthesizer Package I
Vectron Player, Miniscope, Miniscope MK II, U KNOW 007, Blue Synth, EZ Synth, EDS 8i

Synthesizer Package II
Lightwave, Prisma, Inferno, Arpeg 01,

Effects Package I
4-Tap Chorus, AutoPan, AutoWah, Delay LCR, Delay LCR Long, Delay Long, Dither/Shaper, Dual Delay Long, Early Reflector, Harmonic Chorus, Harmonic Flanger, Hexa Chorus, Multitap Delay, Overdrive, Pitch Shifter, Resonator, Ring Modulator, Tremolo, Decimator.

Effects Package II
DC-Filter, De-esser, Ducker, Ducking Delay, MasterChorus, MasterFlanger, MidiPole Filter, MidiTremolo, PatternDelay, RandomFlanger, SoftClip, SpaceFlanger, SSB ModDelay, SSB Modulator, SSB Phaser, StepFlanger, Stereo Expander, Tube Drive, TQ Drive, Vocoder III

Mixer Package I
STM 2448, Dynamic Mixer, Micromixer

STS 2000P
STS 3000
Modular V2
Volkszämpler (Windows only)

There's some devices that are no more installed in SFP, like Bigmixer. You can just copy them from a backup location and load them. If you get a keys request, try your old key or send request for key to CW...

You'll be enjoying SFP much more soon

_________________
10daysoff techno & DnB festival now streaming!!

<font size=-1>[ This Message was edited by: at0mic on 2002-08-02 02:37 ]</font>

If I had a problem like that, I would certainly go back to my last registry so returning to the point of depart. Then I would install anything again, as if never done the mistake.