Page 1 of 1
Posted: Sun May 05, 2002 2:19 pm
by tribadism
With 3 or 4 ms latency my Creamware PowerPulsar ( wave dest ) don't work with soundforge 4.0 or wavelab 3 ....
I don't habilitate at record ...
My system .
AUSU P4B266
install INF and Intel acc.
Powerpulsar z-link
Version Pulsar 3.01b
tribadism@inwind.it
Thank
Posted: Mon May 06, 2002 9:12 am
by subhuman
What OS?
What PCI slot is your PowerPulsar in?
Posted: Mon May 06, 2002 9:17 am
by tribadism
Win98 SE
3° Slot
Thank Subhuman
Posted: Mon May 06, 2002 9:22 am
by subhuman
One more question: what is your CPU speed?
I can run 3ms <i>barely</i> on my 1.8Ghz.. if you have a 1.6A then 4 or 7ms will be better settings to use.
Anything sharing an IRQ with your card? You can check with "Winkey+Pause" combo, Device Manager, Properties... if you could put that list here, it would make the troubleshooting quicker/easier from this end. Thanks!
Posted: Mon May 06, 2002 10:11 am
by tribadism
[quote]
On 2002-05-06 10:22, subhuman wrote:
One more question: what is your CPU speed?
2.14 mhz ( overclock ) original is 1.8a
I can run 3ms <i>barely</i> on my 1.8Ghz..
I have the same CPU
if you have a 1.6A then 4 or 7ms will be better settings to use.
Anything sharing an IRQ with your card? You
Sharing with ACPI !
Posted: Mon May 06, 2002 10:39 am
by tribadism
I made a test
If my pulsar project cancels and puts again
wave dest 1, wavelab or sound forge RECORD !!!!!! works fine .
If I stop recording and try again it doesn't work but if I cancel wave dest 1 and put again .... WORKS FINE !!!! WHY ???
Posted: Mon May 06, 2002 10:52 am
by tribadism
attention
ULLI at 44.1
set at 3ms don't work
set at 4ms don't work
at 7 / 13 or 25ms work fine
Posted: Mon May 06, 2002 11:13 am
by subhuman
ACPI is holding your latency back. Reinstall XP in Standard mode or change HALs. For more information on ACPI/Standard and switching visit the Optimize your Win2k/XP thread in the Tips & Tricks section here.
Posted: Mon May 06, 2002 11:20 am
by tribadism
On 2002-05-06 12:13, subhuman wrote:
ACPI is holding your latency back. Reinstall XP in Standard mode or change HALs. For more information on ACPI/Standard and switching visit the Optimize your Win2k/XP thread in the Tips & Tricks section here.
I don't have Windows XP
. I have only win98 SE ...
What is HALs ????
Is possible disable ACPI into win98 SE ?
Thank Sub
))
Posted: Mon May 06, 2002 11:39 am
by subhuman
Oh, sorry, I read that you were using 9x and then forgot. Very strange results, are you using an older project or something? Anyway if it works then stay with it!
Posted: Mon May 06, 2002 12:00 pm
by tribadism
On 2002-05-06 12:39, subhuman wrote:
Oh, sorry, I read that you were using 9x and then forgot.
No problem
Very strange results,
You think ? Why don't you try to make a test? with PowerPulsar and win98 SE ?
are you using an older project or something?
My test is ONLY wave dest 1 ....
Anyway if it works then stay with it!
:|