Page 1 of 1
96 KHz and Rme ADI-2 doesn´t work
Posted: Thu Sep 06, 2012 2:59 am
by khim-zen
96 KHz and RME ADI-2 doesn´t work for me . I can make 96 KHz work with the boards (Pulsar 2 ) own breakoutcables but there is a lot of noise on the signal and RME ´s converter should be much better.Only one channal is active with ADI 2 in 96KHz .I also have problems with RME and 44.1 KHz but usually I can suppres the problem,pops and clicks , by reloading the drivers or resync.
Anyone have an idea to solve the problem?
Regards Kim
Re: 96 KHz and Rme ADI-2 doesn´t work
Posted: Thu Sep 06, 2012 8:47 am
by garyb
why is the RME i/o much better?
how are you connecting the two systems?
Re: 96 KHz and Rme ADI-2 doesn´t work
Posted: Thu Sep 06, 2012 10:06 am
by Fluxpod
khim-zen wrote:96 KHz and RME ADI-2 doesn´t work for me . I can make 96 KHz work with the boards (Pulsar 2 ) own breakoutcables but there is a lot of noise on the signal and RME ´s converter should be much better.Only one channal is active with ADI 2 in 96KHz .I also have problems with RME and 44.1 KHz but usually I can suppres the problem,pops and clicks , by reloading the drivers or resync.
Anyone have an idea to solve the problem?
Regards Kim
For 96khz you need to go into the pulsar controlpanel>Samplerate and select S/mux A or B depending on what adat port you use.
Re: 96 KHz and Rme ADI-2 doesn´t work
Posted: Thu Sep 06, 2012 10:42 am
by garyb
that is true, if you are slaving to ADAT.
but that's an excellent point Fluxpod! ADAT is 48khz maximum. with 2 sets of ADAT ports(16 channels), you can get 8 channels of 96k using s/mux. this is an ADAT standard, not a Scope or RME thing.
Re: 96 KHz and Rme ADI-2 doesn´t work
Posted: Thu Sep 06, 2012 11:41 am
by khim-zen
Thank you for your answers.
I have tried s/mux .I have tried both slave and master mode but only one channel is monitored.
"why is the RME i/o much better?"
answer:
Signal from RME is almost noiseless and I think the RME converters are better.
Kim
Re: 96 KHz and Rme ADI-2 doesn´t work
Posted: Thu Sep 06, 2012 3:17 pm
by dawman
All the more reason to buy converters from this Century that S|C uses.
Re: 96 KHz and Rme ADI-2 doesn´t work
Posted: Fri Sep 07, 2012 10:27 am
by Fluxpod
Make sure to choose either S/pdif optical or adat.If Adat then S/mux for anything over 48khz! Or if you connect via coaxial S/pdif make sure to run 75 ohm cables.You need to connect 2 cables! In and out to get sync.
Btw the Adi2 is a very good 2 ch converter.
Re: 96 KHz and Rme ADI-2 doesn´t work
Posted: Mon Oct 01, 2012 4:49 am
by khim-zen
My RME ADI 2 still doesn´t work in 96 Khz. Only one channel is monitored. Does anyone use S/MUX from the 4.5 software? I have the idea that S/mux is the problem since only channel 1 works.Another reason could be sync problem. ADI 2 doesn´t have WC-sync and my experience tells me tha ADAT sync is less stable
Re: 96 KHz and Rme ADI-2 doesn´t work
Posted: Mon Oct 01, 2012 10:10 am
by garyb
s-mux uses two channels for each channel of audio.