DSP assignment questions
Posted: Fri Mar 30, 2012 5:58 pm
Hi !
2 questions on DSP assignment:
Project 16Bit 44.1K
All ASIO-2 I/Os, WAVE Source-1 and hardware I/Os on DSP#1
1x VDAT on DSP#2
DSPs #3 - #6 free for the communications w/ the 4 slots.
Slot-1 / DSP#7 / STM2448X / DSP#15 Control Room / DSP#11 B-2003
Slot-2 / DSP#8 / Minimax monophonic (1 voice)
Slot-3 / DSP#9 / Profit-5 (5 voices like the original)
Slot-4 / DSP#10 / Vectron (8 voices like the original)
Question 1:
What´s best for additional MIDI I/O source/destination modules ? - ´cause I´ll need many ports and usage of MIDI OX virtual MIDI cables.
Question 2:
Increasing polyphony for Profit-5 from 5 voices to 6 - 8 voices resulted in DSP limit warning for XITE-1
Is one of the 333MHz SHARCs (DSP#9 here) at it´s limit w/ Profit-5 and 6-8 voices polyphony and doesn´t the DSP routine spill over to the next free DSP (in the same slot),- DSP#17 p.ex ?
The DSP warning disappeard when back to 5 voices for Profit-5 though.
Is there a better solution of DSP assignment for Profit-5 and 8 voice polyphony by re-assigning Profit-5 to any other free DSP in my arrangement above ? (Slot-2 DSPs #12 / 16, Slot-3 DSPs #17 / 13 or Slot-4 DSPs #14 / 18)
Same question might come up when adding UKnow7 synths and a STS 4000 sampler,- or a Modular III.
And there aren´t any FX loaded up to now ...
Bud
2 questions on DSP assignment:
Project 16Bit 44.1K
All ASIO-2 I/Os, WAVE Source-1 and hardware I/Os on DSP#1
1x VDAT on DSP#2
DSPs #3 - #6 free for the communications w/ the 4 slots.
Slot-1 / DSP#7 / STM2448X / DSP#15 Control Room / DSP#11 B-2003
Slot-2 / DSP#8 / Minimax monophonic (1 voice)
Slot-3 / DSP#9 / Profit-5 (5 voices like the original)
Slot-4 / DSP#10 / Vectron (8 voices like the original)
Question 1:
What´s best for additional MIDI I/O source/destination modules ? - ´cause I´ll need many ports and usage of MIDI OX virtual MIDI cables.
Question 2:
Increasing polyphony for Profit-5 from 5 voices to 6 - 8 voices resulted in DSP limit warning for XITE-1
Is one of the 333MHz SHARCs (DSP#9 here) at it´s limit w/ Profit-5 and 6-8 voices polyphony and doesn´t the DSP routine spill over to the next free DSP (in the same slot),- DSP#17 p.ex ?
The DSP warning disappeard when back to 5 voices for Profit-5 though.
Is there a better solution of DSP assignment for Profit-5 and 8 voice polyphony by re-assigning Profit-5 to any other free DSP in my arrangement above ? (Slot-2 DSPs #12 / 16, Slot-3 DSPs #17 / 13 or Slot-4 DSPs #14 / 18)
Same question might come up when adding UKnow7 synths and a STS 4000 sampler,- or a Modular III.
And there aren´t any FX loaded up to now ...

Bud