Page 1 of 2
clock di scope utboard is to be synchronized
Posted: Sun Feb 24, 2008 1:19 am
by nunziata
utboard is to be synchronized
1 scope DSP
A16 ultra 1
1 presonus digimax
1 Roland M1000
Thanks
Posted: Sun Feb 24, 2008 1:23 am
by alfonso
Could you explain your problem a bit better?
How do I synchronize machines?
Posted: Sun Feb 24, 2008 2:47 am
by nunziata
How do I synchronize machines?
Samplerate scope of the errors I
As devop do?
Whereas outboard
Scope DSP 15
Zlink connected with A and B ultra a16
Presonus digimax
M 1000 Roland mixer
And a signal distributor MUTEC 1 in 8 out?
Posted: Sun Feb 24, 2008 1:53 pm
by H-Rave
start off as the scope as master with adat and syncronise the a16 ultra the presonus digimax off that, maybe go out of the digimax with the bnc into the mutec, they will all have to be switched on of course, oh and don't panic, unless you're recording the rolling stones and then you can panic.
hello
Posted: Sun Feb 24, 2008 10:49 pm
by nunziata
In the project that I have inciato in zlink dest must connect the monitors.
For listening.
Right?
Posted: Sun Feb 24, 2008 10:59 pm
by garyb
maybe. you can use the A16 via z-link to the monitors or you can use the analog or sp/dif connectors to the monitors depending on how you set up your project. Scope is a virtual reality patchbay. connect as you please.
Hello, do you know syncplate?
Posted: Thu Feb 28, 2008 2:03 pm
by nunziata
Hello, but the form syncplate where you connect?
What?
Perhaps we need to set 16 as the master if you want to use the 16 channels
Posted: Thu Feb 28, 2008 6:01 pm
by garyb
no the A16 doesn't need to be master. if you are using the syncplate, the connections are external bnc. within scope, you select bnc as master, OR if scope is set to master, clock will be transmitted through bnc and adat.
please help me
Posted: Thu Feb 28, 2008 10:14 pm
by nunziata
But because 'I will not do a project?
Like 'I see the better argument:
Example hardware I.
Thanks a lot
Posted: Thu Feb 28, 2008 11:35 pm
by garyb
obviously there's a language problem.
nothing problem
Posted: Fri Feb 29, 2008 5:53 am
by nunziata
No problem, just send a project that displays what has been said.
There is a problem doing this?
Thanks
Posted: Fri Feb 29, 2008 12:45 pm
by garyb
yes. if i unerstood you and you understood me i could just tell you.
i don't understand the problem.
you don't need to do anything special to sync samplerates in the project. no syncplate module is required.
Excuse my insistence
Posted: Sat Mar 01, 2008 12:48 am
by nunziata
Yes, but regardless if I can not put it, the project can mandarmelo?
So 'schiarisco my best ideas.
This was my initial application.
Thanks anyway
Posted: Sat Mar 01, 2008 1:05 am
by garyb
mandarmelo?
'schiarisco?
Posted: Sat Mar 01, 2008 2:43 am
by H-Rave
Babelfish
Posted: Sat Mar 01, 2008 3:13 am
by garyb
sure is...
Posted: Sat Mar 01, 2008 10:57 pm
by nunziata
Sorry for my English.
Through the same
Posted: Sun Mar 02, 2008 12:24 am
by garyb
no problem. sorry i couldn't help.
Posted: Sun Mar 02, 2008 4:40 am
by H-Rave
Nunziata :
Through the same
Stop it !
That's my Idea ??
ok
Posted: Sun Mar 02, 2008 5:32 am
by nunziata
Ok but who is the master?