Copy protection bs....

[Shroomz~>]

I haven't actually had prompts for copy protection issues unless I was missing a key or Scope was confused about board id's.

Board ID confusion was my first thought on this & it might still be the case, but I'm really not sure. I had this error message just last week in the sdk when dropping/moving a new circuit into the parent module of one of my previous projects (It's a fully/properly working stereo effect project that I'm using these days as a core for building effects).

[Shroomz~>]

according to reports (long ago) these messages sometimes used to popup related to multiprocessor systems and virus protection software in the past...

cheers, Tom

As mentioned, I get these messages occasionally on our main Scope/SDK system, but there's no virus protection software on there & it's not a multiprocessor system.

[Fluxpod]

according to reports (long ago) these messages sometimes used to popup related to multiprocessor systems and virus protection software in the past...

cheers, Tom

As mentioned, I get these messages occasionally on our main Scope/SDK system, but there's no virus protection software on there & it's not a multiprocessor system.

Hmm i try to turn ht off in the bios.
If that doesnt work i completly uninstall scope remove the cards clean the reg then add 1 card after another..i think i messed something up by switching slots and adding the pro srb at once..maybe not that good idea todo that.
But..BUT what if that still does not fix it..thats what scares me a little...

[Fluxpod]

Didnt worked..oh well,will have a busy afternoon tomorrow

I decided to wait for the keyfile.If that doesnt fix it i will uninstall everything.
No idea tho why it still happens,i try to turn off xtc mode later but i am already just shooting in the dark.
Thanks for all the help tho i keep you posted here.

[Fluxpod]

If anyone has more ideas:p Please chime in,gary maybe?
Very thankfull for any bits of help.

[garyb]

wait for the keyfile.

the cards have a flash rom that holds all the keyfile data. sometimes some of the data becomes corrupt. a new set of keys should fix that.

[Fluxpod]

wait for the keyfile.

the cards have a flash rom that holds all the keyfile data. sometimes some of the data becomes corrupt. a new set of keys should fix that.

Thanks gary! I try to be patient.

[garyb]

i'm praying that the keyfile does it.

[garyb]

it doesn't necessarily help, but it can't hurt....

[Fluxpod]

Maybe found the reason.My pulsar 2 key which i sended to ralf was wrong.It ends with an I in the reg window but shows an R as last letter on the card sticker.

This is teh wiered...guess i get the new keyfile tomo.

To continue.

[Fluxpod]

Meh!Got the new keyfile from ralf today(thank you btw for fast service)but it didnt fixed anything....my p2 still shos with an I at the end of the registry and it is def an R on the card sticker.
As this pissed me off i will reinstall sfp tomorrow i had 4.0 and now i dlled the 4.5 version.
And if that does not work i format the pc.
This error blows......

EDIT and to add in the keyfile the p2 card also has an R at the end..WTF???....
Corruption of data of hell...so lame ....

[Shroomz~>]

Sorry to hear that mate. I'd suggest getting the cards into the slots that produced the ideal 0,1 order before the reinstall, but ultimately you might have to reinstall the whole system.

Mark

[garyb]

open the keyfile that you got from Ralf with notepad and see what the serial number is in there. does it match the card?

perhaps it's never been right and one of the other card's keys were what you were using....

[Fluxpod]

Thanks guys.The keys in the .reg match the card stickers but the p2 key changes to an I at the end (instead of R on the p2 stcker) after importing it.I have 0 idea why but i will reinstall the sfp software tomorrow.The cards work and everything is totally fine,on seperate not shared irqs,can load enought masterverbs for the system etc.Just need to figure this out as the plugs from the 14 dsp srb wont load.Thats a real bitchy problem...maybe with testing i can write a little guide for people who may have the same issue.
After the sfp reinstall i will try again and if THAT wont fix it i take out all cards and install them 1 by 1.I maybe screwed up when moving pci slots and stuff...atleast i hope i did:P
Thanks again for all your help i post the results of the journey tomorrow.

[Shroomz~>]

I'd bet that it works just fine if the key/s for the M&M pack are registered to a board other than your SRB.

Mark

[Shroomz~>]

Sorry, I should have said.... If all else fails.... "I'd bet that it works just fine if the key/s for the M&M pack are registered to a board other than your SRB."



Mark

[Fluxpod]

but why? The synths that are regged on the srb also dont work.I bite the bullit later and do a fresh install with reg cleaning.
Thanks again.

[Fluxpod]

Uninstalled sfp 4.0 and installed 4.5.
Same as before haha..ahh man...i did expect that.....
The srb keys wont show up in the registry even when importing the keyfile.
Odd fun.
So i guess i have to unmount all cards and start with the p2 then the srb then the p1.
Great..not that i have other stuff todo lol......I will put in the cards 1 by 1 restart and check and so on.be back in ....5 hours or so lol

[Fluxpod]

So when i try to install the srb alone it wont accept the keyfile...sfp wont let me click continue after i try to import the .rgy.
Before i erased 4.5 it asked for the key at startup but gave me the 0001 error cant start sfp.
Pc off putting p2 to it.
After putting the p2 back in i could install sfp..keys from the srb not accepted it sees only the p2 keys......

I spare myself the hazzle to put the p1 back in for now..
Could the srb be messed up somehow??
It came from the uk and i absolutly believe geoff that it worked when he send it.Could the rom on it get corrupted by xraying the card at the airport??
Shooting in the dark here but as sfp wont install the keys on it at all but shows the correct sn in the install window..baffled now.

[Fluxpod]

Emailed ralf...at this point that shit is pissing me off so much..i am out of any ideas now and i guess the srb rom got screwed up.

Edit: Can anyone confirm these 0001 errors.Searching the forums brought up a few topics where the card had to be send in.
Wiered thing is i can use the dsps but not the plugs and that makes me think something is screwed up with the card itself.