PlanetZ forums - scopeusers.com

I have the problems on ableton live 9.0 (official) and on ableton live 9.1 (beta) as well.
I solved now the problem by using M4L "CC sender 16". Then i could automate the synths. But sometimes i use a knob from xtc synth with the mouse and push doesn't react anymore, ableton is then froozen but ...

I read that push uses a special midi protocoll to reach higher midi performance. There it could be true. There are different behaviours of midi assignment:

a) if i use right mouse button to assign midi from push, then midi signal is recognized from xtc synth. But if i turn the knob in push, then ...

Hi,

i just installed ableton live 9.1 beta. I want to run scope cards with xtc. I work with SFP 4.0.

All synths and effects are recognized from live and they work.

What is not working is as follows:

I move one xtc-synth to midi track. then i play and record midi, works fine. Then i assign some ...

Hi,

i want to set another fundamental frequency for my scope synths. Hardware synths offer this sometimes, VST-Plugins as well. How can i do this for scope synths like prodysey, minimax, vectron a.s.o? I cannot see a switch to do this. Perhaps i can do this for the whole sonic-core hardware as well ...

Hi,

what i heared about the origin of goa is Israel. From Israel goa was transfered to the area "goa" of india. Then they portated it world-wide. Perhaps there exist other opinions...

I found a nice link like that: http://www.youtube.com/watch?v=4Hi1_7f4L_Y
I love this kind of video and the ...

Hi,

all the time i search some tips about goa and trance production by using scope systems. At the moment i am not sure if i know all the necessary or possible synths and effects of sonic-core, 3rd-party-plugins or freeware for sonic-core. Therefore i opened this thread to discuss this subject ...

Hey stardust,

thank you very much for the answers.

One last question:

I want to use the FLT 64 Asio with 32 stereo channels. If i route the MixL/R to an asio dest channel then i will lose one channel for my tracks. Do you know a solution how to realize full 32 stereo channels?

Greetings...

Hi stardust,

thank you for your post. But i have some question for you. Would be nice if you could answer me. Thank you.

In your first post of this thread you describe the typical project. For this i have some questions:

First you described as follows:
"...basically you route each track to an ...

I tried all entries described here, but i have still 24ms delay. I use Scope, PulsarII and Elektra. Scope is the host. What could be the problem?

Hi,

what is the age of the card? Do you deliver it to europe as well?

Hi, how much do you want without plugins?

Ok, then my consumption is to work with cubase until the new version 11 of samplitude will be announced.

With cubase i can controll the mixer, controll all effects and synths in one sequencer without special configurations. I hope that samplitude will extend there sequencers for this subject.

At ...

Hey voidar, thank you for the tip.

Hi siriusbliss,

thanks for your answer. What do you mean to put my hardware in the signature?

Hi nightscope,

thanks for your comments about samplitude and there possiblities about midi.
I tested samplitude 10.1 to prove thats samplitude is able to automate XTC plugins. Unfortunately i have to say there is no support. I work with BCF2000 in Mackie Control Mode and Samplitude.

The results ...

Hm, i feared it. Perhaps there exists another solution in XTC.

One question about Y wire:

You are right that it is possible to insert the Y wire into Vinco sidechain inserts. But unfortunately this configuration is not saved into vinco. If you save your cubase project and reopen cubase afterwards then the Y wire is disapeared. This is a bug of all scope ...

Hi,

i try to automate Scope synths by using Samplitude. By pressing right mouse button i am able to assign wished controller of my hardware controller. Moving the hardware controller knob gives me control about the synth knob. But if i move the knob by using the mouse the sequencer doesn't send the ...

If you use asio fp 32 bit and you open the setup of scope in the sequencer then you will see the possible selection 16Bit or 24Bit. But i want use 32 bit. Therefore i selected the asio fp 32 bit..

Do you know what i have to do to ensure the 32 bit mode?

What is the name of the old and new motherboards?