PlanetZ forums - scopeusers.com

Hi,

thanks for your statement, Gary, but one of the prolems on actual boards is to prevent IRQ-sharing foc Scope-boards with other devices. If you can't choose the IRQ in the BIOS, it is nearly impossible to assign a privileged IRQ to the Scope cards.

Stardust, I thougt ACPI-mode causes problems ...

Hi,

I want to ask the community which actual mainboard (AMD or Intel) is ok for Scope.
I want to install 3 cards (2x Pulsar2 and 1x Scope prof.), but a lot of actual mainboards don't have the feature to assign irq's to the pci-slots.

On elder boards (ASUS CULS2-C f.e.) it was possible to change ...

Hi Garyb,

thanks a lot for your statement. I bought a new set of lightpipes and changed from 44,1 to 48 KHz - and it's running! The DAW was for a year unused in a cellar, may be the pipes were old.

Thanks and bye

Christian

Hi,

I want to use a DAW with a Luna + ADAT-Extension, a scope professional and a syncplate, setted up with a 1 GHz Intel and Windows XP, sequenzer is Cubase 5.1 :-) It works fine using a Tascam DM24 with 24 Ch via firewire, but I need this mixer in another setup.

My problem: Now I want to connect ...

Hi,

the solution: deleting the screensets and creating new ones with the new positions.

Thanks a lot!

Christian

Hi,

I use a Matrox 550 with two Monitors, Cubase on the right, Scope on the left.

But the problem is the same on a single monitor system, when I put the Mixer on an other place, the position will not be saved. When I recall it, the mixer position is the same as at startup.

Any hints? Is the ...

Hi,

I'm using a two-monitor-system with sfp 4.0 and it isn't possible to save the window-positions on the windows desktop, f.e. of the routing window or optimaster. Every time I use the tings I find the original window position. Saving the szene with the corrected window positions doesn't help.

Is ...

Hi,

I'm using a two-monitor-system with sfp 4.0 and it isn't possible to save the window-positions on the windows desktop, f.e. of the routing window or optimaster. Every time I use the things I find the original window position. Saving the szene with the corrected window positions doesn't help ...

Hi

I use a LunaII with Logic 4.7 Silver software and all works fine with the two analog inputs.
Now I added the ADAT-Expansion with a 8-Channel Analog-ADAT-Interface for using ten analog inputs and the trouble begins:

I routed all in the Luna software, I get input in my Luna mixer on all ten ...

Hi atomic,

thanks for ultra-speed-reply, I'll try it!

Bye

Christian

Hi,
I want to use a Luna II with I/O-expansioncard together with a Pulsar SRB or Pulsar 1. It works, but I can only use the ULLI-settings of the Pulsar 1 down to 13ms.

I remember that I read here about the fact, that if you combine two cards of the first and second generation it would be possible ...

Hi,

I use the DM 24 as Master, changing the ADAT-Ports I didn't try.
What is a word clock generator? An external hardware device? I never heard of a standalone device.

Bye

Christian

_________________


<font size=-1>[ This Message was edited by: fortner on 2004-07-08 03:46 ]</font>

Hi,
I use a Tascam DM 24 via 2x ADAT (16 CH) and a Pulsar1. All works fine, but sometimes the system is going out of sync (noise, no signal). After restarting scope 4.0 all will be normal until the next time.

CULS2-C, PIII 1000MHz, Matrox G450, all tweaked, standard mode.

The DM 24 has a BNC-sync ...

Hi,

I'm working with two pc-systems (PIII 1000MHz and P4 2GHz) with Intel-based-motherboards, all tweaked and imho well prepared as DAW, but there are a lot of problems: IRQ, PCI-capacity, crackles, noise etc.
It's possible to configure a perfect working pc, but it is a lot of work (testing ...

Hi garyb,

I found a message of atomic who said, that the lowest possible pci latency is the best choice.
How to do?

Bye

Christian

Hi,

I tweaked all, standard mode at installation is the first to do.

What's about PCI-Latency in BIOS-Setup? Default is 32, are there better values?

Bye

Christian

Hi,

sorry, 2ms isn't possible with the Pulsar 1, but with the Pulsar 2...

Working with a Mac there are PCI-problems like on the Intel-platform? Perhaps it works batter on a Mac.

Bye

Christian

Hi,

ASUS CUSL2-C with 512 MB, PIII 1000MHz, Matrox G450, XP Home tweaked, latest drivers. The DSP-load is with two Mastererbs about 60-70 percent - not too much.

With Masterverbs as insert in Aux 1+2 I can use 13ms Latency at 41KHz, without Masterverbs 96KHz and 2ms is possible. I dont believe in ...

Hi,

I bought a second hand Pulsar 1 for my second recording-pc and got some problems with crackles. I use a 1632 mixer with two masterverb classic as aux-effects 1 and 2.

I notice glitches and crackles from the mixer 1632, wave1 source works fine with cd.

The first masterverb is loosing the ...

Hi,

thanks for your tip, it works after connecting the sources and destinations.
I created a generic file with my needed controls, HUI-Mode isn't supported under Cubase 5.

Thank you very much

bye
Christian