PlanetZ forums - scopeusers.com

Hello AGAIN!!!!

I think I have cracked it all but one slight problem.

When I have the system synced up, the studio manager software will move the faders on the hardware mixer freely, but when I move the hardware mixers faders there is resistance.

Anybody any suggestions??

Hi again, I have tried what you have said but I am still getting the same error message.

Everything appears to be ok in Pulsar as the adat port is highlighted red within the Samplerate settings.

But the weird thing is that I am now getting constant clicks and pops.

I have also lost the use of ...

Cheers people I will give your ideas a go!!!

No doubt I will be back though

Hi, Gary

Thanks for your reply; I have tried to answer as best as possible

“what are the master/slave relationships?”

I am not too knowledgeable about this; I think I have the Pulsar as master and the 01V as slave. I would be grateful if you could give a few pointers on this.


“are the cables ...

Could anyone give me a tutorial with setting a Pulsar 2 with a Yamaha 01v96?

This has been driving me nuts for the last two weeks.

I have set the 01v at 44.1 and 16 bit but cannot get the pulsar to sync with Cubase 5.1 and the Yamaha

I have hooked it up via ADAT, but get the message "Sync error ...

spirit, the last project I was working on successfully was before I upgraded to 3.1a

this is the first time it has ever happened to me, it has happened ever since I loaded up the new 3.1a
has any1 had anything like this???????????????????????????????????

I am still having the same problems, does any1 else have any ideas. The problem is with all projects
cheers

Can any1 tell me what this means on starting my project this message comes on screen
"pep add routing:pads source switch.in17 and source switch. out are incompatible, cannot route" after I ok this none of my synths work and my system crashs all the time
please help

I, have this problem as well on my pc I would be grateful if someone could help, as well as this when I use cubase my song when loaded up completely crashs every 5 minutes.
huge headaches

with the new 3.1 does any1 know how to route external wave editors such as sound forge as i am having no luck and no sound

Cheers Sub, I have just run through the install again I had not fully watched what I was doing and did not change from luna to pulsar on the start up
Cheers again
Thompsy

Cheers Subhuman, I have already used the allkeys file while loading the new sfp that is why I am lost on how to find the synths. Do you have any other ideas on this problem

I was just wondering if any1 could help with a problem with my 3.1 software I have loaded up the new software but when I go into the pulsar program and start a new project I cannot find the synths on my screen I have went through the manual but cannot find any info on this. If this is me being dumb ...

Cheers for your help I have got it working now, Wont be long til I have another problem

I have done what you have told me me but I am getting feed back or there is a stereo recording going on in the loop while I am recording. Can you you tell me where the loop is in Pulsar( I am only using the Pulsar card at home, I only have my PC no other outboard gear, but when I recorded in college ...

what I mean by convert is!!!
1. Left and right Locate around midi
2. Enable Audio (in Cubase)
3. Record
4. Audio channel 1 (for example)
Then all the midi files when cubase punches out should mixdown to channel 1
sorry if this is simple I am an Amature

When I try and convert midi to audio all I get is a flatline, this is doing my head in as when I convert to audio in college with my project there is no problem can any1 help me (I think it is a pulsar problem rather than Cubase)

I am sorry to sound really stupid, but I have tried all you have said, the best I have got is loading the 'new program' on channel 1 which works then when I try and load the samples onto channel 2 it fails (if this is the right way do this I am going by what technical support at London SCV told me ...

I have just read your hints(although I have not tried in practise) SubHuman, where do I get the new sts manual. sorry if this was an easy question to answer!!!! Thank you